COLD AIR INTAKE FOR 2020-2022 SILVERADO / SIERRA DURAMAX L5P 6.6L

Vehicle Application

• YEAR: 2020
• MAKE: Chevrolet
• MODEL: Silverado 2500/3500
• ENGINE: 6.6L Duramax

Tools Required

• Socket Wrench
• 8mm, 10mm, 13mm Socket
• ¼” Socket Extension
• 5/16” Socket/Nut Driver
• T20 Torx
• Phillips Head Screwdriver

S&B Filter Maintenance

KF-1076 Cotton Cleanable : If the enclosed filter is RED, it came pre-oiled from the factory.

KF-1076D Dry Extendable : If the enclosed filters is WHITE, it is a disposable filter and should be discarded once it reaches capacity. This filter does not require oil.

Periodically Check the Following

• Intake Tube (T) and Filter (AB) connections and Intake Box (A) fasteners making sure they are tight.
• All electrical connections and wire harnesses moved during the installation of the intake and make sure they are secure and away from any hot or moving components.
• Check for any signs of abrasion or wear and tear on the intake tube, box, filter, and electrical harnesses moved or near the intake and repair/replace as necessary.

Before You Start

• Please read the entire product guide before proceeding.
• Ensure all parts are present.
• If you are missing any of the components, call our customer support at (909) 947-0015.
• Do not work on your vehicle while the engine is hot.
• Make sure the engine is turned off and the vehicle is in Park or the Parking Brake is set.

Performance Testing

After your installation is complete, engage the parking brake and start your engine. Listen for abnormal noises. If an air leak is detected, re-inspect hoses and connections as they may need to be repositioned and tightened.

S&B FILTERS recommends that you keep your OE intake system in the event it is required in the future.

In order to maintain your warranty, all connections and components must be checked periodically for alignment and for proper tension on all connections. Failure to do so may void your warranty.

Use only S&B FILTERS cleaning and oil products to service your filter. Using any other brand oil and or cleaners on your S&B air filter may void your warranty

Air Box Plug Testing

Stock air boxes are a significant contributor to poor airflow which is why S&B designs custom air boxes with secondary and/or enlarged openings. With that said, S&B recognizes the benefits of cooler air, so we have included a plug to seal off the opening if so desired. For optimal performance, we recommend that the intake be used without the plug except in conditions of extreme heat.

Operation in Rain or Snow

If you are driving in heavy snowfall or extreme rain conditions, you should always check for accumulated snow and water on the air filter. The following is recommended after operating the vehicle up to 100 miles in heavy snowfall or extreme rain: At the earliest opportunity, open the hood and check the airbox and filter. If any snow has accumulated, make sure to remove the snow from the filter, box, and inlet. It is ok if the filter is a little wet. Wet filters will normally dry out on their own. If the filter is dripping wet, it should be replaced with another filter that is not wet. Do not reuse the dripping wet filter until it has naturally dried.

Warning!

If your vehicle has a Vehicle Emission Control Information decal affixed to the factory airbox, a new replacement label must be obtained and installed in a readily visible position in the engine compartment in order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check. Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall not be affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood on a painted surface, is recommended

CARB Status - Pending

CARB EO # Pending

*Not Legal for use in CA and other states adopting CA emissions Standards.

Emission Standard

The California Air Resource Board (CARB) requires that an E.O. Identification label be applied to the vehicle in order to pass a smog check inspection when a Performance Intake Kit has been installed. You must place the E.O. Label provided on or near the intake kit after installation so that a smog check technician can easily verify the E.O. Number. Check the status of the exemption process by looking up a specific part number at www.sbfilters.com. The CARB Exemption number and/or status is listed under the Product Details section for each part number. If the status shows as “Pending,” CARB has yet to issue an exemption but the product has been submitted. Products that have not been issued an E.O. number are street legal in most states, but may not be used on emission controlled vehicles in the state of California. If you purchased your kit from S&B Filters directly, we will automatically mail you your Exemption Sticker when it is issued to us. If you purchased your kit from an authorized S&B Filters Dealer, log onto our website and register to receive your Exemption Sticker.

Related Products

• S&B Filter Maintenance: (KF-1076)
• Dry Extendable Filter (KF-1076D)
• Cleaning & Oiling Kit (88-0008)